News

The core calculation method of the resolution and size of Rental LED Display   1. Module resolution and screen resolution The module resolution is obtained by multiplying the number of horizontal and vertical pixels in a single LED module. For example, if a module has 128 pixels horizontally and 64 pixels vertically, its resolution is 128×64. The screen resolution is determined by the number of modules that make up the entire screen and the module resolution. Assuming that the above modules are spliced into a 2×3 (horizontal×vertical) screen, the screen resolution is: (128×2)×(64×3)=256×192 The key logic is: the total number of pixels on the screen is equal to the number of pixels in a single module multiplied by the number of modules arranged.   The screen size is determined by the module size and the number of modules. Take the P3.91 indoor LED panel (500×1000mm) as an example: the size of a single module is 500mm (width)×1000mm (height). If two modules are spliced horizontally and one module is spliced vertically, the total screen size is: (500×2)mm ×(1000×1)mm = 1000mm×1000mm If a 2000mm wide wall needs to be covered, 2000÷500=4 modules need to be spliced horizontally.   The dot pitch (such as P3.91, P1.9) indicates the center distance between adjacent LED beads, which directly affects the resolution and viewing distance. The smaller the dot pitch, the higher the pixel density per unit area. For example:   The P3.91 module has about 64,000 pixels per square meter (1000÷3.91²≈64,000) The P1.9 module has about 274,000 pixels per square meter (1000÷1.9²≈274,000) The choice of dot pitch requires a balance between resolution and cost. The pixel density of P1.9 screen is more than 4 times that of P3.91, but the cost increases by about 3-5 times.       II. Scientific calculation of viewing distance of Rental Led Screen The viewing distance needs to take into account visual comfort and picture detail recognition. The following two methods are commonly used:   1. Industry experience formula The closest viewing distance (clear pixel recognition): The closest distance (meter) = dot pitch (mm) × 1000 ÷ 1000 For example, the closest viewing distance of P3.91 screen is 3.91 meters, and pixel particles may be seen below this distance. The best viewing distance (overall sense of the picture): The best distance (meter) = dot pitch (mm) × 3000 ÷ 1000 For example, the best viewing distance of P3.91 screen is 11.73 meters, and the picture is delicate and grainless within this range.   2. Calculation based on resolution and screen size The vertical viewing angle is calculated by the screen height and resolution, and then the viewing distance is derived:   Calculate the number of pixels corresponding to the screen height. For example, a 1000mm high P3.91 screen has a vertical pixel count of about 1000÷3.91≈256 pixels. Calculate the distance based on the vertical viewing angle of the human eye (recommended ≤30°): Viewing distance (meters) = screen height (meters)÷(2×tan(15°)) For example, the viewing distance of a 1-meter high screen is about 1÷(2×0.2679)≈1.86 meters.   III. Typical product features and scene adaptation of Led Screen Rental Take P3.91 and P1.9 small-pitch LED screens as examples to analyze their technical advantages and applicable scenarios:   P3.91 screen Dot pitch 3.91mm, resolution density 64,000 pixels/㎡, optimal viewing distance 3.9-11.7 meters. Suitable for scenes such as conference rooms, exhibition halls, medium and large stages, cost controllable, suitable for long-distance viewing.   P1.9 screen The dot pitch is 1.9mm, the resolution density is 274,000 pixels/㎡, and the optimal viewing distance is 1.9-5.7 meters. It is suitable for scenes such as command centers, high-end conference rooms, virtual shooting, etc. The picture is extremely delicate and suitable for close-range high-definition display.     Differentiated design of P3.91 500×1000mm panel Lightweight and fast deployment The weight of a single module is ≤15kg, and it supports single-person hoisting; the positioning pin design makes the module splicing accuracy reach ±0.1mm. High protection The corner guard device can withstand a 1-meter drop impact; the bottom gap design prevents damage to the LED lamp beads during transportation. Flexible splicing Supports mixed splicing of 500×500mm and 500×1000mm cabinets, and can build curved screens (curvature radius ≥2 meters) or special-shaped screens. High refresh rate guarantee The 3840Hz refresh rate eliminates shooting moiré and meets the needs of 4K/8K video live broadcast.   4. Selection recommendations and cost optimization Select dot spacing based on viewing distance When the audience is ≤5 meters away from the screen, it is preferred to select small pitch below P2.5; when the distance is >10 meters, P3.91 or larger dot spacing products are more cost-effective. Balance resolution and cost If you need to display text as the main feature, you can appropriately reduce the resolution (such as P4.81); if you need to play high-definition video, the recommended resolution is ≥1920×1080 (corresponding to a P2.5 screen of about 2.3 meters high). Maintenance convenience The front maintenance design (such as magnetic suction module) can save more than 50% of maintenance time and is suitable for high-frequency use scenarios.

Outdoor high-definition grille transparent window LED display (hereinafter referred to as "grid transparent screen") is a translucent display device designed for scenes such as commercial windows and building curtain walls. Its core features are:   Grille light bar design: adopts a horizontally or vertically arranged light bar array, and the light bar spacing is usually P3.91 to P10, forming a "hollow grille" structure with a light transmittance of 60% to 85%. This design not only ensures the penetration of light, but also achieves clear display through the high-density lamp beads on the light bar. Ultra-thin and lightweight: The screen body is only 8 to 15 mm thick and weighs no more than 12 kg/m2. It can be directly installed on the glass without additional reinforcement of the building structure. It is easy to install and low-cost. Balance of high light transmittance and high-definition display: By optimizing the lamp bead packaging technology (such as COB or GOB) and the light bar spacing, 1920×1080 or higher resolution is achieved while maintaining high light transmittance, which is suitable for close viewing.     Comparison with other types of LED screens:   With traditional outdoor LED screens: Traditional screens are fully enclosed and completely opaque, suitable for billboards and other scenes; grille transparent screens take into account "display + light transmission", suitable for scenes such as windows and curtain walls that need to retain background visibility.   With indoor transparent screens: Indoor screens have low brightness (usually ≤1500cd/m²) and cannot adapt to strong outdoor light; grille transparent screens have a brightness of ≥5000cd/m², which can meet daytime visibility needs.   With outdoor grid screens: Grid screens have higher light transmittance (up to 95%), but extremely low resolution (usually above P10), and obvious grids can be seen at close range; grille transparent screens strike a balance between resolution and light transmittance, suitable for scenes that need to take into account clarity and light transmittance.         3. Application scenarios and advantages analysis   Commercial window scenario:   Advantages: Product and advertisement superposition display: Customers can see the products behind the screen through the screen and watch dynamic advertisements at the same time, which improves the conversion rate (according to statistics, the conversion rate increases by 15% to 30%). Energy saving and consumption reduction: Compared with traditional screens, energy consumption is reduced by 40%, and long-term operating costs are lower. Immersive experience: Supports naked eye 3D, interactive touch and other functions to enhance customer participation.   Building curtain wall scenario: Advantages: Do not damage the appearance of the building: Keep the glass curtain wall transparent during the day, play dynamic light shows at night, and enhance the city's aesthetics. Lightweight design: The weight is only 12 kg/m2, no need to reinforce the building structure, and the installation cost is reduced by 50%.   Scenic area guide scenario: Advantages: Information and landscape integration: Installed on the glass plank road or viewing platform in the scenic area, it displays the guide information without blocking the scenery. High protection level: IP68 waterproof and dustproof, adaptable to extreme weather such as rain, snow, sand and dust.

In the fast - paced world of visual tech, the LED display market defies economic headwinds, posting steady growth. This surge stems from relentless technological innovation and its rising adoption across diverse sectors.​ Emerging regions like Asia, Africa, and Latin America are driving demand. As infrastructure booms, LED display light up cityscapes — towering billboards dominate streets, while vibrant screens steal the show at local events. In the film industry, LED virtual shooting walls replace green screens, letting directors visualize complex scenes in real - time. Cinemas, too, upgrade to LED for a more immersive movie - watching experience. Rental LED display, known for their quick setup and portability, have become event planners’ go - to, whether for concert backdrops or exhibition booths.​ Future Trends​ Tech advancements are reshaping the LED landscape. Micro - pitch technology refines pixel density, delivering crystal - clear visuals even for close - up viewing in financial trading floors or museums. Transparent LED displays transform retail windows, blending digital and physical elements to showcase products. Flexible panels free designers from conventional shapes, enabling curved or irregular installations in galleries and restaurants.​ Naked - eye 3D and holographic displays are revolutionizing entertainment. Theme parks now feature life - sized holographic characters, and concerts wow audiences with floating performers. Meanwhile, retailers use LED for 3D product showcases and AR try - ons, while transportation hubs rely on them for real - time traffic updates. On stages, LED screens with dynamic backdrops elevate live shows.​ Market Offerings​ The market’s LED products cater to varied needs. Rental displays, with modular designs and high refresh rates, ensure smooth visuals and easy assembly, perfect for festivals and corporate events. Outdoor LED screen, built tough with high protection ratings, withstand harsh weather. Their front - access design simplifies maintenance, making them ideal for long - term installations like roadside billboards.​ Indoor and outdoor signage displays offer multiple pixel pitch options, paired with intuitive content management systems. Whether a small café advertising daily specials or a mall running a digital screen network, these displays deliver. High - brightness outdoor LED models, unfazed by sunlight, are a top pick for large - scale ads and sports broadcasts.​ As the industry marches forward, LED displays will unlock more potential, powering innovation across countless industries.

Stroll through the city, and you can’t miss them. Outdoor LED Displays are everywhere—towering over busy streets on building walls, sharing real-time info at train stations, and even brightening up shop windows. Among them, Floor Standing Outdoor LED Posters stand out with their sleek looks, catching the attention of pedestrians as they walk by. These aren’t just advertising tools; they’ve become a lively part of city life, making our urban world more vibrant and interactive.​ Advertising Led Displays work wonders in crowded places. Their sharp images and moving ads easily grab people’s attention, even in the hustle and bustle of the city. Take the LED display boards at intersections, for example. They’re not only great for promoting products but also for sharing important updates like traffic conditions and public notices, showing they’re useful in many ways. And the best part? Energy Saving Led Display tech means these bright screens use less power, helping businesses save money and be more eco-friendly. What really makes these displays special is the customization. Outdoor Custom Led Signs can be made to match any brand’s style, whether it’s a simple, elegant sign for a small store or a big, flashy logo for a well-known company. Then there are the Oudoor Led Window Displays, perfect for local shops. They turn plain windows into eye-catching showcases that make people stop and take a closer look. Making these high-quality displays isn’t easy. It takes years of know-how and the latest technology to get them just right. By teaming up with reliable partners, we can use the best materials and ensure each display is tough and long-lasting, giving you great value for your money.​ We know every client has different needs, so we offer personalized service from start to finish. Our team will help you design the perfect display, install it, and take care of any maintenance. No matter if you’re a new business trying to make a name for yourself or a big company looking to boost your advertising, our LED solutions can help your brand stand out. Get in touch today and let’s create something amazing together!

​The LED display industry is undergoing rapid technological evolution, significantly enhancing display capabilities and visual experiences across various sectors.​ Technological Advancements Drive Market Expansion​The global LED display market is on an upward trajectory. As per TrendForce, driven by Micro/Mini LED and automotive lighting, the global LED market is set to reach $13.003 billion in 2025, representing an 8.2% growth over 2024.​ Industry players have introduced a range of advanced products. Indoor LED displays now support up to 6K refresh rates, while outdoor ones can reach 8K, ensuring high - speed motion is depicted clearly. 14 - 15Bit grayscale technology enables seamless color transitions, and a wide color gamut close to 120% NTSC results in vivid and accurate colors. In the Mini/Micro LED segment, new “decoration material” - style displays solve black - level uniformity issues. When inactive, they blend with architectural surroundings, integrating functionality with aesthetics. Transforming Visual Experiences in Diverse Sectors​ Business and Office​LED displays are essential for modern smart meetings. Their high refresh rates and accurate color reproduction help present data, charts, and videos clearly, facilitating communication and decision - making. Large digital signage in offices disseminates announcements, streamlining workplace operations.​ Culture and Arts​LED displays are creating immersive experiences in the cultural and artistic domain. High - dynamic contrast technology showcases fine details in stage art. Creative LED displays, including spherical and folding screens, add unique visual effects. At music festivals, spherical LED screens synchronize visuals with music, delivering a 360 - degree experience.​ Retail and Advertising​LED displays serve as powerful marketing tools. High - protection and energy - saving outdoor displays can convey messages even in harsh weather conditions. In malls, customizable LED displays promote products and brand stories, tailoring to the store’s theme and enhancing the shopping experience. ​Future Outlook​The advent of 5G + 8K ultra - high - definition video technology opens up new opportunities for the LED display industry. Market players are expected to continue innovating, making advanced LED display technology more accessible and driving global digital transformation. In the future, we can anticipate higher resolution, improved energy efficiency, and more flexible display designs, further enriching visual experiences.​

In recent years, with the rapid development of science and technology, LED Display has been widely used in various activities, especially Rental Led Display and stage Led Display has become a frequent guest in performances, conferences and other occasions. However, although the LED screen brings a shocking visual effect, it also has some shortcomings that cannot be ignored.   For the rental of LED displays, the high rental costs are often a big burden. In particular, some large-scale performances or activities, in order to pursue the perfect stage effect, have to invest a lot of money to rent high-quality stage LED display. In addition, the stage LED screen is also quite cumbersome in the installation and disassembly process, requiring professional technicians to operate, which undoubtedly increases the cost of manpower and time.   In addition, the brightness of the LED display can not be underestimated. Although the high-brightness screen can maintain a clear display effect in a strong light environment, watching the high-brightness LED screen for a long time will have a certain impact on the audience's vision. Especially in some closed or semi-closed places, too bright screens are easy to cause discomfort to the audience.   To sum up, although the rental LED display and Stage Led screen have brought unprecedented visual impact to various activities, the problems such as high cost, cumbersome installation process and possible impact on the audience's vision still need to be faced and solved. In the future, we look forward to further breakthroughs in science and technology to bring us more perfect and convenient LED display solutions.

In recent years, LED technology has advanced significantly, leading to innovative applications and designs. One of the most intriguing questions in the industry is, "Can LED screens be transparent?" The answer is a resounding yes, and our company is at the forefront of this exciting development. Transparent LED screens are revolutionizing how we think about displays. Unlike traditional opaque screens, transparent LED screens offer a sleek, modern look that can blend seamlessly into various environments. This technology allows for the creation of displays that don’t obstruct views, making them perfect for applications where visibility is key. An standout product is the Outdoor LED Curtain for Building. This display is designed specifically for outdoor use, combining durability with transparency. It’s perfect for creating impressive, eye-catching visuals on building facades while still allowing natural light to filter through. At our company, we’re proud to offer several cutting-edge products that utilize this transparent LED technology. Our LED Curtain Display is a prime example. This product features a translucent design that makes it ideal for use in high-traffic areas and architectural installations. It provides a stunning visual effect without blocking light or scenery. For more extensive installations, our LED Curtain Wall Display offers a versatile solution. This display is ideal for large-scale projects where both visibility and transparency are crucial. It can be used in a variety of settings, from commercial spaces to public areas, providing a sophisticated way to showcase content while maintaining an open feel. We also offer the LED Strip Curtain, a flexible and innovative option that can be customized to fit different shapes and sizes. This product is particularly useful for creating dynamic, transparent displays that can adapt to various design requirements. In summary, transparent LED screens are not just a possibility but a reality, thanks to the advancements in technology. Our range of products, including the LED Curtain Display, and LED Strip Curtain, demonstrates our commitment to providing cutting-edge solutions that blend seamlessly with their surroundings. Whether you’re looking to enhance a building’s facade or create a unique visual experience, our transparent LED displays offer the perfect solution.

Diving Into the World of UHD Indoor LED Screen Technology UHD indoor LED screens are a revolutionary technology that turns ordinary visuals into extraordinary displays with their vibrant clarity and colors. Picture stepping into a stadium, shopping mall, conference room, or command center and being greeted by visuals so bright and clear they feel almost lifelike. This is the power of an Indoor UHD LED Display Screen Panel, which has become immensely popular for bringing static images and videos to life in various indoor settings. What's Inside a UHD Indoor LED Screen? Breaking it down into simple components, here’s what you’ll find inside these advanced devices: LED Modules: The very heart of the Indoor High Definition LED Screen. These modules are like tiny lights working in unison to paint a picture. Organized neatly in a grid, they create the big, beautiful image you see on the display. Processor: This component ensures that whatever you wish to display looks impeccable on the screen. It fine-tunes aspects like size, color, and frame rate, making sure everything appears as it should on your Indoor LED Video Wall Display. Power Supply: Much like any gadget, these screens need power to illuminate. The power supply ensures a consistent flow of electricity, keeping the screen up and running smoothly. Control System: The brains of the operation, this system integrates both software and hardware to give you control over the display. Whether it’s tweaking brightness levels or switching up the content, the control system has you covered. How It All Comes Together The journey of an image or video to your LED screen begins with a video signal from a source, like a computer or media player. The processor then steps up, optimizing this signal to ensure it translates beautifully on your Indoor UHD LED Display Screen Panel. Next, the optimized signal is sent to the LED modules. Here, each LED lights up in red, green, or blue, working together to form the dynamic, full-color image that captivates viewers. Beyond just displaying visuals, the control system vigilantly ensures the image quality remains pristine, making instant adjustments to combat flickering or color discrepancies. In essence, UHD indoor LED screens, with their advanced LED technology, have revolutionized how we perceive images and videos indoors. Whether it's an Indoor LED Video Wall Display or an Indoor High Definition LED Screen, these panels promise to deliver a visual experience that’s nothing short of spectacular, making them indispensable for any indoor environment aiming to make a statement with vivid, lifelike visuals.

Outdoor transparent led screens are suitable for the exterior wall of the mall, highway landmarks, and other scenes that can be viewed at close range. The pixel distance between outdoor transparent screen is usually between P3.91 ~ P15.4, and the transparent led display screen is relatively clear. Outdoor transparent led display also have IP65 waterproof capacity. Outdoor work is all -weather, and installation and maintenance are support front/Rear maintenance. Features: 1.Light weight cabinet The weight as light as 8KG/Sets and the thickness is 10mm.All Aluminum body,Anti UV. Sutible for big panel size or old building. 2.High transparency Beautiful wind and light through design .Transparency up to 40%,and it has strong wind pressure resistance.Realize Media value also light the building ,Sunlight can get through freely,People from inside have good view of outside. 3.Low power consumption,high heat dissipation Outdoor transparent led display is energy saving. Average power consuption is about 320W/M2. No need air conditionor and other cooling system. 4.High brightness High brightness 8000CD/m2,Can show images under the sunlight,attract visitors from a long distance 5.Hight IP grade Cabinet has IP66 from back and front. No need extra protection. 6.Fast installation & maintenance Easy installing,No need complex frame structure,We will design and provide Cost effective and easy structure for installation,Could help to save cost.

If the LED display fails, it is definitely troublesome to the industry. But trouble is used to solve, but how do you solve these problems? Today, I will learn about the 10 methods of the LED display failure to eliminate the failure of the LED display. .First, the display is not working, the sending card green lights flash (made into a collection type) 1. Failure cause: a. There is no power supply; b. The network cable is not connected well; c. No power supply or power supply voltage for receiving cards; d. The delivery card is bad; e. Signal transmission intermediate device connection or failure (such as: functional card, optical fiber receiving box); 2. Failure exclusion method: 1) Check the normal power supply of the screen body; 2) Check the re -connecting network cable; 3) Make sure the power supply output power supply is 5-5.2V; 4) Replace the delivery card; 5) Check the connection or replace the function card (optical fiber receiving box); .Second, the display is not working, the send card green light does not flash 1. Failure cause: A.DVI or HDMI lines are not connected; b. There are no settings for copying or extension in the graphics card control panel; c. The software selected a large -screen power supply; d. The delivery card is not inserted or there is a problem with the delivery card; 2. Failure exclusion method: 1) Check the DVI cable connector; 2) Set replication mode; 3) Software selection to turn on the large -screen power supply; 4) Re -insert send card or replace the send card; .Third, prompt "the big screen system is not found" when starting 1. Failure cause: a. The serial line or the USB line is not connected to the sending card; b. Computer COM or USB port bad; c. serial port or USB line bad; d. The delivery card is bad; e. No USB driver installed 2. Failure exclusion method: 1) Confirm and connect the serial line; 2) Replace the computer; 3) Replace the serial line; 4) Replace the delivery card; 5) Install the new version of software or install the USB driver separately .Fourth, long strips such as lamps are not displayed or partially displayed or lack of color 1. Failure cause: a. Flat lines or DVI lines (applicable to submarine series) are not well contacted or disconnected; b. Show the lamp at the transfer of the former output or the latter input is problematic 2. Failure exclusion method: 1) Re -insert or replace the line; 2) Determine which display module is faulty and then replace repair . Some modules (3-6 blocks) are not displayed 1. Failure cause: a. Power protection or damage; B.AC power cable is not good contact 2. Failure exclusion method: 1) Detection and confirm that the power supply is normal; 2) Re -connect the power cord . The entire box is not displayed 1. Failure cause: A.220V power supply line is not connected well; b. There are problems with network cable transmission; c. Receive card damage; d. Hub board insertion misplaced 2. Failure exclusion method: 1) Check the power supply line; 2) Confirm the replacement of the network cable; 3) Replace the receiving card; 4) Re -insert HUB , the whole screen, the spots, the picture and the shadow, the new movement 1. Failure cause: a. Driver loading program is wrong; b. The network cable of the computer and the screen is too long or the quality is not good; c. The delivery card is bad 2. Failure exclusion method: 1) Re -operate loading the receiving card file; 2) Reduce the length of the network cable or replace; 3) Replace the sending card . Each display unit of the entire display displays the same content 1. Failure cause: No display screen connection file is not sent 2. Failure exclusion method: reset the sending the screen file, and connect the network cable that connects the computer when it is sent to the output port of the transmission card near the indicator light .the display screen is very low, and the display image is blurred. 1. Failure cause: a. The delivery card program error; b. Function card settings are wrong 2. Failure exclusion method: 1) Restore the sending card default settings and save; 2) Set the maximum brightness value of the display screen monitoring is 80 or more; . Shake the entire screen screen or shadow 1. Failure cause: a. Check the communication line between the computer and the large screen; b. Check the DVI line of the multimedia card and the delivery card; c. The delivery card is bad. 2. Failure exclusion method: 1) Put the communication line or replace; 2) Pour DVI cables and reinforce; 3) Replace the sending card.

With the continuous development of science and technology, led display screen has been widely used in life, but not everything is as expected, led display screen often has the problem of protection level during use, what performance does LED screen outdoor have , can withstand the sun exposure? Many customers will worry about this problem, of course, the led screen is good. But spending so much money to install a LED screen outdoors can't stand the sun and rain, it feels very worthless. Outdoor LED displays generally have a large area, so they are still very heavy. LED display installed outdoors, the home page needs to pay attention to the design of the structure. The installation structure should take into account: wind resistance, earthquake resistance, bearing and other main factors; secondly, the shape, structure, and exterior decoration design of the screen should be coordinated with the attached building or environment; thirdly, it is to consider local environmental factors, Such as air humidity, air salinity content and so on. In order to withstand the exposure of the sun, the LED display must use environmentally friendly materials. After special technology, without glue, the LED display module can achieve the environmental protection purpose of being waterproof, dustproof, and UV-proof. When customers choose led display products, they need to clarify their own needs for LED display, such as product application site, environmental analysis, product expectations, comprehensive analysis of various reasons, in order to choose a suitable product. When the LED display screen is working, especially after the sun exposure, the heat emitted by the screen body is relatively high. In order to ensure that the entire display screen system operates in a stable state, the research on the display screen cooling system has a set of strong convection heat removal. system. In addition, the heat conduction effect of aluminum is used to make the cooling system more stable and reliable.

I remember reading this line in an article: "The Internet has eaten everything. It has eaten television, it has eaten print, it has eaten newspapers, music and books. But it has not and will never eat outdoor media." Many outdoor LED billboards have become a beautiful landscape, integrated with urban buildings and become part of the landmark! Outdoor large LED screen advertisements have been sticking to their posts for many years. Some people may think that they are used to its existence and have little effect on themselves. However, when shopping, he will think of this outdoor advertisement, and even choose to buy the product. Therefore, we found that outdoor advertising does not have no effect on consumers. In fact, they have memories of the content of the advertisement, and the audience receives the content of the advertisement unconsciously. When exposed to the product again, short-term memory kicks in, influencing its final decision. Outdoor advertising has a subtle impact on consumers' psychology, leaving an impression in consumers' subconscious, thus playing a role in consumers' purchasing decisions. Under the premise of making full use of the media scene environment and space, outdoor LED large-screen advertising can mobilize a variety of on-site expression methods to create a comprehensive and rich sensory stimulation, images, sentences, three-dimensional objects, dynamic sound effects, environment, etc. can be combined ingeniously. At the same time, using AR interactive 3D naked eye and other technologies, the large-screen media interacts with the mobile Internet terminal, realizing a seamless connection between offline and online.

Many friends will be concerned about the price when purchasing LED screens, but there are many factors that affect the price of LED screens. The low price is one thousand yuan per square meter, and the expensive one is tens of thousands per square meter. see it 1. LED Display specifications From the color, the LED display can be divided into dan color, two-color, full-color, and from the use environment, it can be divided into indoor, outdoor, semi-outdoor, and the price of each type of led screen is different. LED Displays with the same point spacing are generally more expensive outdoors than indoors. Outdoor led screen will be equipped with technical requirements such as waterproof, dustproof, and sunscreen. 2. LED Display model Generally, the smaller the point spacing, the clearer the point, and the higher the natural price. For example, the price of P3 led screen will be higher than that of P5 led screen. 3. LED Screen Display area The larger the area, the higher the price will naturally be. 4. LED Screen Display shape Common special-shaped screens are cylindrical, round, square or Rubik's cube, etc. The more difficult the shape, the more expensive the price; 5. LED Display raw materials Among the raw materials, light-emitting chips (light tubes) are currently the main factor affecting the price of LED screens. In addition, there is also LED driver IC, which is a very important factor affecting the quality and life of the led display. If the led display screen is used in very important occasions, it is recommended to choose imported light-emitting chips, constant current and constant voltage driver ICs to be more secure. Other materials that affect the price are power supplies, cabinets, and various accessories for making led displays. 6. LED Display supporting system a. System accessories: sending card, receiving card, transfer card; b. Playing system: control computer, multimedia card or graphics card, playing software; c. Editing system: editing computer, video compression card, editing software; d. Monitoring system: sensor + monitoring software; e. Protection system: cooling system, power distribution system, lightning protection system; f. Sound system: amplifier + speaker; g. Video input equipment: DVD/VCD player, VCR, CCTV; h, graphic input: scanners, digital cameras. Except for the system accessories and playback system, the above accessories and equipment are optional equipment. Due to the influence of factors such as brand and procurement channels, the price of its LED display is naturally different. 7. Construction factors Affected by factors such as installation location, installation method, construction difficulty, screen size, frame structure selection and other factors, especially when making LED outdoor billboards, due to the construction environment, the project price varies greatly. 8. Other factors: Factors such as payment method, tax rate, transportation method, manufacturer's purchase cost, and production cost all determine the quotation of LED display. The above are the main factors that affect the current LED screen quotation. I believe that after reading it, you will have a clearer understanding of the LED price. Here, I would like to remind you that when buying LED screens, you must choose the source manufacturer, not only the quality It is guaranteed, and the after-sales service is timely, so you can buy with confidence Our company Shenzhen Priva Tech Co., Ltd. is an enterprise specializing in the research and development, production, sales and service of LED display screens. Anti-corrosion, more than 20 patents, soft writing, industry certificates and other authoritative qualifications. The current factory is located at 5th Floor, Building 2, Zhuoke Science Park, Shenzhen, Guangdong, China .The main products are: outdoor led screen, indoor led screen, small pitch led screen, special-shaped screen, transparent led screen, LED grille curtain display, etc.; ★Die-cast aluminum cabinet, high-definition full color, never black screen; ★Standard flame retardant material, resistant to extreme temperature, can work normally at -20℃-40℃; ★No need to install air conditioner, save about 30% energy than similar products; ★Waterproof IP68, can work normally underwater; ★Maintenance before and after, can be disassembled by one person;

Recently PRIVA presented new products-Rental Led Displays for large event Stages LED Screen and indoor or outdoor Stage Led screen. It ranges from a few square meters to several thousand square meters. High Resolution Background LED screen Wall, with excellent image performance, will bring an amazing experience to the viewer. Stage LED Video Wall high – quality production technology. With a simple splicing design. Size:500*500*82mm/500*1000*82mm Weight:7.5Kg/12.5Kg Pixel pitch:Indoor:P1.9/P2.5/P2.6/P2.9/P3.91 Outdoor:P3.91/P4.81 Serivce method:Front/back

Recently PRIVA presented new products-Rental Led Displays for large event Stages LED Screen and indoor or outdoor Stage Led screen. It ranges from a few square meters to several thousand square meters. High Resolution Background LED screen Wall, with excellent image performance, will bring an amazing experience to the viewer. Stage LED Video Wall high – quality production technology. With a simple splicing design. It has become the most popular stage background product for large – scale stages, weddings, trade shows, hotel training, etc Advatages:

Transparent LED screen have become a rising star in the display field, and naturally become one of the popular choices for users in many industries. However, in the actual demand process, factors such as model, size, and viewing distance need to be comprehensively considered, which undoubtedly makes it more difficult for users to recognize. Let's talk about the factors that need to be paid attention to when choosing LED transparent display. Transparent LED Display Selection Guide and Points to Note: 1. The dot pitch and resolution are closely related, and product selection should pay attention to the application In the current small-pitch LED market, permeability, dot pitch, large size and resolution are the key points of manufacturers' technical PK. In practice, these factors also affect each other, and the specific dot spacing must be matched with the appropriate transparent screen size to achieve the best display effect. 2. The selection of LED transparent screen brightness Full indoor display. Including: indoor stage, exhibition hall, conference room, etc. The indoor light is dim, and the brightness of the transparent LED display should be controlled between 800-1500nits. It is recommended not to exceed this brightness range. If it is too bright, it will appear too dazzling, affect the viewing effect, and also consume more electricity. Semi-outdoor display. Including: shopping malls, sales offices, etc. The semi-outdoor light environment is better than indoors, and the brightness selection should be controlled at about 2000-3500nits to ensure the normal display effect of the transparent screen. When the LED transparent screen faces no sunlight, it is perfectly satisfied according to the customer's environment of 3000CD-4500nits; when the LED transparent screen faces the sun, the low-brightness transparent screen will appear blurred pictures due to insufficient brightness. The brightness selection should be around 5000-6000nits to meet the normal display effect in a strong sunshine environment. 3. Large-sized products must fully consider maintenance costs In practical applications, not only the high purchase cost but also the maintenance cost should be considered when selecting large-size products. Although the theoretical life of LED lamp beads can reach 100,000 hours, because high-density LED transparent screens are mainly used in indoor applications, the products are required to be light and thin, and the thickness should be low. , it will make it difficult to dissipate heat, and the probability of local failure will be high. In actual operation, the larger the screen size is, the more complicated the maintenance will be, and the maintenance cost will increase accordingly. Therefore, for large-size products, users must choose on demand. 4. The combination of signal transmission equipment cannot be ignored The signal compatibility of the LED transparent screen is very important. If the signal access requires a variety of requirements, the number is large and the location is scattered, it usually includes video signals in H.264, 720P, 1080P and other formats. When purchasing a product, you should avoid paying attention to the product unilaterally. The resolution must be fully considered whether the existing signal equipment supports the corresponding video signal.

In the outdoor LED large screen environment, the quality requirements are higher, and there are many factors to be considered. 1. From the perspective of the application of LED large screen, LED large screen full color screen is the mainstream in the future. Because of the high brightness and full color, it can work all day, but the price is high. 2. From an application point of view, there is a reason for a product that meets user needs. Due to its cheap price, maturity and stability, the dual-primary color display has a large market in terms of no blue characters and color display. 3. The direction and distance of the outdoor screen play a decisive role in the price. The farther away, the larger the pixel and the brighter it is. Displays in the northeast are much less expensive than those in the southwest. 4. The joint between the screen and the building must be strictly waterproof and leak-proof. The filter should adopt good drainage measures, and once there is accumulated water, it can be discharged smoothly. 5. Install lightning protection devices on LED displays and buildings. The display body and the casing are well grounded, the grounding resistance is less than 3, and the large current caused by lightning can be discharged in time. 6. Install ventilation equipment for cooling to ensure that the internal temperature of the screen is between -10-40. A fan can also be installed at the rear of the screen to dissipate heat. 7. Select an industrial-grade integrated circuit chip with a working temperature of -40-80 to prevent the screen from not starting when the temperature is too low in winter.

According to the different surface treatment technology of LED display screen, we can divide it into plug-in module, table-mounting module, sub-table-mounting module, three-in-one table-mounting module and three-in-one table-mounting module. Plug-in module It refers to the DIP encapsulated lamp which passes the lamp foot through the PCB board and fills the tin in the lamp hole by welding. The module made by this process is the plug module. The advantages are large angle of view, high brightness and good heat dissipation. The disadvantages are low pixel density. Surface mount module SMT, also known as SMT, solders the SMT encapsulated lamp on the surface of PCB board by welding process, the lamp foot does not need to pass through the PCB board, and the module made by this process is called SMT module. The advantages are: large perspective, soft display image, high pixel density, suitable for indoor viewing; the disadvantages are that the brightness is not high enough, and the lamp tube itself does not heat well. Subsurface Mounting Module It is a product between DIP and SMT. The packaging surface of LED lamp is the same as SMT, but its positive and negative pins are welded through PCB in production as DIP. Its advantages are high brightness, good display effect, and its disadvantages are complex process and difficult maintenance. Three-in-one table sticker It refers to encapsulating three different colours of LED wafers, R, G and B, in the same colloid. The advantages are: simple production, good display effect, and disadvantage: difficult spectrophotometry and high cost. Three-in-one sticker It refers to the vertical juxtaposition of three independent packaged SMT lamps, R, G and B, according to a certain distance, which not only has all the advantages of the three-in-one, but also solves all the disadvantages of the three-in-one. From the above classification, we can see that different classification modules have their own advantages and disadvantages, so when we make the LED display screen, we should classify according to the actual application situation and the scene situation.

The IP (International Protection) protection level system for LED display screen was drafted by IEC (International Electro Technical Commission). The lamps and lanterns are classified according to their characteristics of dust-proof, foreign invasion-proof, waterproof and moisture-proof. The objects referred to here include tools, human fingers and so on. They can not touch the charged part of the lamp, so as to avoid electric shock. IP protection level is composed of two numbers. The first number represents the level of dust-proof and foreign invasion prevention of lamps and lanterns, and the second number represents the degree of sealing of moisture-proof and water-proof invasion of lamps and lanterns. The bigger the number, the higher the level of protection. The two numbers indicate the level of protection as follows: IP protection level: The first indication of the degree of protection indicated by the characteristic number (number) The first number is: 0 unprotected IP0- 1. Prevent solid objects larger than 50mm from intruding and human body (such as palm) from accidentally touching parts inside lamps. Prevent large size (diameter greater than 50mm) objects from intruding into IP1- 2. Prevent solid objects larger than 12 mm from intruding into the lamp and prevent human fingers from touching the parts inside the lamp. Prevent medium-sized (diameter greater than 12 mm, length greater than 80 mm) objects from intruding into IP2- 3. Prevent the intrusion of solid objects larger than 2.5mm, tools, wires or similar small objects larger than 2.5mm in diameter or thickness from touching the interior parts of lamps IP3- 4. Prevent the intrusion of solid objects larger than 1.0 mm, tools, wires or similar small objects larger than 1.0 mm in diameter or thickness from touching the interior parts of lamps and lanterns IP4- 5 Dust-proof, completely prevent foreign invasion. Although it can not completely prevent dust intrusion, the amount of dust intrusion will not affect the normal operation of lamps IP5- 6. Dust tightness completely prevents foreign matter from intruding, and also completely prevents dust from intruding into IP6- The second indicates the degree of protection indicated by the characteristic number (number) The second indicator number: 0 unprotected IP-0 with no special protection for people or objects outside 1. Prevent drip intrusion. Vertical drip (e.g. condensate) will not cause harmful effects on lamps and lanterns IP-1. Dripping water can still be prevented when the lamp is inclined to 15 degrees. When the lamp is inclined from vertical to 15 degrees, dripping water will not cause harmful effects on the lamp IP-2. 3. Prevent the invasion of sprinkled water, prevent rain or water sprayed in the direction of vertical angle less than 60 degrees from entering the lamps, causing damage to IP-3 4. Prevent splashing water from intruding into lamps, and prevent splashing water from entering lamps in all directions, causing damage to IP-4 5. Prevent the water from spraying into the lamp and damage IP-5 by spraying water from all directions. 6. Prevent the intrusion of big waves, install lamps on deck, and prevent the damage IP-6 caused by soaking due to the invasion of big waves. 7. Prevent water intrusion during immersion. Lights immersed in water for a certain time or under a certain water pressure can ensure that IP-7 is not damaged by water inflow. 8. Prevent water intrusion during sinking, and ensure that IP-8 is not damaged by water inflow under the condition of specified water pressure for indefinite sinking of lamps and lanterns.

According to the different surface treatment technology of LED display screen, we can divide it into plug-in module, table-mounting module, sub-table-mounting module, three-in-one table-mounting module and three-in-one table-mounting module. Plug-in module It refers to the DIP encapsulated lamp which passes the lamp foot through the PCB board and fills the tin in the lamp hole by welding. The module made by this process is the plug module. The advantages are large angle of view, high brightness and good heat dissipation. The disadvantages are low pixel density. Surface mount module SMT, also known as SMT, solders the SMT encapsulated lamp on the surface of PCB board by welding process, the lamp foot does not need to pass through the PCB board, and the module made by this process is called SMT module. The advantages are: large perspective, soft display image, high pixel density, suitable for indoor viewing; the disadvantages are that the brightness is not high enough, and the lamp tube itself does not heat well. Subsurface Mounting Module It is a product between DIP and SMT. The packaging surface of LED lamp is the same as SMT, but its positive and negative pins are welded through PCB in production as DIP. Its advantages are high brightness, good display effect, and its disadvantages are complex process and difficult maintenance. Three-in-one table sticker It refers to encapsulating three different colours of LED wafers, R, G and B, in the same colloid. The advantages are: simple production, good display effect, and disadvantage: difficult spectrophotometry and high cost. Three-in-one sticker It refers to the vertical juxtaposition of three independent packaged SMT lamps, R, G and B, according to a certain distance, which not only has all the advantages of the three-in-one, but also solves all the disadvantages of the three-in-one. From the above classification, we can see that different classification modules have their own advantages and disadvantages, so when we make the LED display screen, we should classify according to the actual application situation and the scene situation.